Maintaining your Noma snowblower is essential for ensuring its optimal performance and longevity. A crucial aspect of this maintenance is adjusting the clutch, which plays a vital role in transmitting power from the engine to the auger and impeller. Here’s a comprehensive guide to help you adjust the clutch on your Noma snowblower with precision and ease.
Firstly, it’s important to understand the function of the clutch in your snowblower. Essentially, the clutch acts as a coupler, allowing you to engage or disengage the power transmission to the auger and impeller. When the clutch is engaged, the auger and impeller can rotate, enabling you to clear snow effectively. Conversely, when the clutch is disengaged, the auger and impeller stop rotating, allowing you to move the snowblower without clearing snow.
The clutch adjustment procedure on a Noma snowblower is straightforward and requires minimal tools. Before starting the adjustment, ensure that the snowblower is turned off and the engine is cool. Additionally, wear appropriate safety gear, including gloves and eye protection, for your safety. Now, let’s dive into the step-by-step process of adjusting the clutch on your Noma snowblower.
Tightening the Clutch Travel Nut
The clutch travel nut is found on the side of the snowblower and is responsible for tightening the clutch cable. When the nut is loose, the clutch cable can become slack and cause the snowblower to slip or engage erratically. To tighten the clutch travel nut, follow these steps:
1. Locate the clutch travel nut. It’s usually found on the side of the snowblower, near the engine.
2. Use a wrench to turn the nut clockwise. Do not overtighten the nut.
3. Check the clutch cable tension. The cable should be slightly slack, but not loose enough to touch the snowblower’s housing.
4. Adjust the nut as needed. Repeat steps 1-3 until the clutch cable tension is correct.
5. Test the snowblower. Start the snowblower and engage the clutch lever. The snowblower should engage smoothly and without slipping.
6. Retighten the nut if necessary. After running the snowblower for a few minutes, check the clutch cable tension again. If it has loosened, tighten the nut a little more.
7. Lubricate the clutch cable. Apply a small amount of snowblower cable lube or automotive grease to the clutch cable to help it move smoothly.
8. Inspect the clutch cable periodically. The clutch cable is a wear item and should be inspected regularly for signs of damage or fraying. If the cable is damaged, it should be replaced.
How To Adjust And Clutch On Noma Snowblower
To adjust the clutch on a Noma snowblower, follow these steps:
- Locate the tensioner screw on the side of the clutch housing.
- Use a screwdriver to loosen the tensioner screw.
- Turn the clutch pulley to adjust the tension on the belt.
- Tighten the tensioner screw to secure the pulley in place.
To adjust the friction disk on a Noma snowblower, follow these steps:
- Locate the friction disk on the side of the clutch housing.
- Loosen the two nuts that hold the friction disk in place.
- Adjust the friction disk so that it contacts the clutch pulley evenly.
- Tighten the two nuts to secure the friction disk in place.
People Also Ask
How do you adjust the drive cable on a Noma snowblower?
To adjust the drive cable on a Noma snowblower, follow these steps:
- Locate the drive cable bracket on the side of the transmission housing.
- Loosen the bolts that hold the drive cable bracket in place.
- Adjust the drive cable so that there is approximately 1/4 inch of slack in the cable.
- Tighten the bolts to secure the drive cable bracket in place.
How do you adjust the idle speed on a Noma snowblower?
To adjust the idle speed on a Noma snowblower, follow these steps:
- Start the snowblower and allow it to warm up for a few minutes.
- Locate the idle speed screw on the side of the carburetor.
- Use a screwdriver to turn the idle speed screw clockwise to increase the idle speed or counterclockwise to decrease the idle speed.
- Adjust the idle speed so that the engine runs smoothly and does not stall.
How do you replace the impeller on a Noma snowblower?
To replace the impeller on a Noma snowblower, follow these steps:
- Disconnect the spark plug wire from the spark plug.
- Remove the bolts that hold the impeller in place.
- Pull the impeller off the crankshaft.
- Slide the new impeller onto the crankshaft.
- Tighten the bolts to secure the impeller in place.
- Reconnect the spark plug wire to the spark plug.
